Watch Wiki

The Best Watches and Watch Brands

User Tools

Site Tools


chronograph
You were redirected here from Cam switching.

Chronograph

A Chronograph is a type of watch or movement that records the passage of time.

Definition of the term

A chronograph is a watch with additional short-time measurement (stopwatch), shown by an additional hand (chrono hand) which can be started, stopped, and reset to zero by pushers in the housing wall.

Most chronographs feature one or more hands on a dedicated dial or subdial to show recorded seconds, minutes, and hours. These are often referred to as totalizers, recorders, or registers since they keep track of elapsed time.

Column wheel vs. Cam switching

It is critical that the various wheels that control a chronograph are synchronized. There are two methods currently in use to accomplish this One where the chronograph function is controlled by a column wheel, the other with the control function by a coulisse lever system (also slotted lever shift or cam switching).

  • The more expensive version is the column wheel chronograph, also called a pillar wheel or (Swiss) castle. In this system, the start, stop, and reset of the chronograph hands is controlled via a column with seven- or nine-tooth gear. This makes the operation of the buttons smoother but is technically very demanding to design and manufacture. Therefore watches with this construction, mostly popular in the 1930s and 1940s, today are regarded as coveted collector's items. Today, many high-end chronographs still rely on column wheels.
  • The chronograph construction via cam switching has a lower 'prestige' but is technically quite capable. In this system, a stack of various-shaped plates operate the various levers required to engage and disengage wheels and stop and start hands. Cams are simpler and less expensive to manufacture, so this system is usually used in lower-end movements. (German term Nockenschaltwerk)

Vertical clutch

Traditional chronographs engaged and disengaged the chronograph wheels using an oscillating pinion, a simple lever which drove the gear teeth together. This abrupt system was effective but problematic, since it was possible for the gear teeth to be damaged over time. It also caused issues with timekeeping, since engaging the chronograph could reduce the amplitude of the movement.

A more elegant system of engagement uses a vertical clutch, similar to the type found in automobiles. This is a more complex solution and demands greater precision of manufacture but has the benefit of smoother engagement and disengagement of the chronograph mechanism and less interference with the timekeeping wheels. For this reason, many advanced and upscale chronograph movements use a vertical clutch.

Buttons

Most chronograph watches use two buttons The top (at 2 00) starts and stops the chronograph counter while the bottom (at 4 00) resets the counter to zero. Some (including the Landeron calibres 48, 51, 148 and 248) use the bottom button to stop and reset with the top only starting the operation.

Some early chronographs, and a few modern homages, use a single button. These so-called monopusher chronographs use a single button to start, stop, and reset the chronograph function in sequence. A range of “timer” watches from various brands are examples of modern monopusher chronographs.

Automatic chronographs

Today even many watch fans don't know that it is only since the year 1969 that chronographs with automatic winding have been manufactured. The race to develop an automatic chronograph included two Swiss/American groups Heuer/Breitling/Dubois Dépraz/Buren/Hamilton with their microrotor Chronomatic, and Zenith/Movado with their high beat central rotor El Primero. Seiko also brought their own automatic chronograph to market at the same time.

Probably the most successful automatic chronograph movement ever built is the proven and robust calibre Valjoux 7750 by ETA, which is built into most of today's mechanical chronographs in many variants. Other well-known movements are the (no longer produced) Lemania 5100 and the in-house Rolex manufacture movement 4130. Many high-end Swiss manufacturers produce their own such movements today.

The measuring accuracy of chronographs

The measuring accuracy of chronographs depends directly on the oscillation frequency (amplitude) of the movement and of the balance wheel.

  • The above movement El Primero is a so-called fast oscillator with 36.000 semi-vibrations per hour (= 5 Hz). This corresponds to an accuracy of 1/10 second.
  • Today at Swiss movements the most common amplitude is 28,800 A/h (4 Hz), which gives a precision of 1/8 second.
  • 21,600 A/h (3 Hz) results in 1/6 second.
  • 18,000 A/h (2.5 Hz) results in 1/5 second.

Literature

chronograph.txt · Last modified: 03.07.2022 15:33 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki

© Watch Wiki. All texts are protected by copyright. The respective copyright holders are the signatories of the contributions. For details see Impressum. Regarding objections and complaints (copyright and other rights) also see there. Impressum | Privacy Policy | Copyright | About Watch Wiki